linux shell有一套自己的流程控制语句,其中包括条件语句(if),循环语句(for,while),选择语句(case)。下面我将通过例子介绍下,各个语句使用方法。
一、shell条件语句(if用法)
if语句结构[if/then/elif/else/fi]
if 条件测试语句
then
action
[elif 条件
action
else
action
]
fi
如果对于:条件测试语句不是很清楚,可以参考:linux shell 逻辑运算符、逻辑表达式详解
shell命令,可以按照分号分割,也可以按照换行符分割。如果想一行写入多个命令,可以通过“’;”分割。
如:
[chengmo@centos5 ~]$ a=5;if [[ a -gt 4 ]] ;then echo ‘ok’;fi; ok
实例:(test.sh)
#!/bin/sh
scores=40; if [[ scores−gt90]];thenecho“verygood!”;elif[[ scores -gt 80 ]]; then echo “good!”; elif [[ $scores -gt 60 ]]; then echo “pass!”; else echo “no pass!”; fi;
条件测试有:[[]],[],test 这几种,注意:[[]] 与变量之间用空格分开。
二、循环语句(for,while,until用法):
for循环使用方法(for/do/done)语法结构:
* _1.for … in 语句_*
for 变量 in seq字符串
do
action
done
说明:seq字符串 只要用空格字符分割,每次for…in 读取时候,就会按顺序将读到值,给前面的变量。
实例(testfor.sh):
#!/bin/sh
for i in (seq10);doecho i; done;
seq 10 产生 1 2 3 。。。。10空格分隔字符串。
2.for((赋值;条件;运算语句))
for((赋值;条件;运算语句))
do
action
done;
实例(testfor2.sh):
#!/bin/sh
for((i=1;i<=10;i++));do echo $i; done;
while循环使用(while/do/done)while语句结构
while 条件语句
do
action
done;
实例1:
#!/bin/sh i=10; while [[ i−gt5]];doecho i; ((i–)); done;
运行结果:========================
sh testwhile1.sh 10 9 8 7 6
实例2:(循环读取文件内容:)
#!/bin/sh
while read line;do echo $line; done < /etc/hosts;
运行结果:===================
sh testwhile2.sh
127.0.0.1 centos5 localhost.localdomain localhost
until循环语句语法结构:
until 条件
do
action
done
意思是:直到满足条件,就退出。否则执行action.
实例(testuntil.sh):
#!/bin/sh
a=10;
until [[ $a -lt 0 ]];do
echo $a;
((a—));
done;
结果:
sh testuntil.sh
10 9 8 7 6 5 4 3 2 1 0
三、shell选择语句(case、select用法)
case选择语句使用(case/esac)语法结构
case $arg in pattern | sample) # arg in pattern or sample ;; pattern1) # arg in pattern1 ;; *) #default ;; esac
说明:pattern1 是正则表达式,可以用下面字符:
* 任意字串 ? 任意字元 [abc] a, b, 或c三字元其中之一 [a-n] 从a到n的任一字元 | 多重选择实例:
#!/bin/sh
case $1 in start | begin) echo “start something” ;; stop | end) echo “stop something” ;; *) echo “Ignorant” ;; esac
运行结果:======================
testcase.sh start start something
select语句使用方法(产生菜单选择)语法:
select 变量name in seq变量
do
actiondone
实例:
select ch in “begin” “end” “exit” do case $ch in “begin”) echo “start something” ;; “end”) echo “stop something” ;; “exit”) echo “exit” break; ;; *) echo “Ignorant” ;; esac done;
运行结果:
说明:select是循环选择,一般与case语句使用。
以上是shell的流程控制语句,条件,循环,选择。 欢迎讨论交流!